Automotive Replacement Batteries

LiFePO4 12V 200Ah Lithium Iron Phosphate Battery Pack, Light Weight LiFePO4 Battery for RV, Solar, Marine, and Off-Grid Applications BMS included

#ad
RUIXU #ad - Ruixu lifepo4 battery deep cycle rechargeable lithium iron phosphate batterythe highest quality lithium iron phosphate technology, the fariest priCE ON THE MARKETIn most standard 12, 24 or 48 volt systems the best choice of lithium battery is LiFePO4 lithium Iron Phosphate. The voltage of this type of battery is very similar to an AGM and will work great with readily available system components for your RV, Boat or Off-grid power system.

Backup and off grid battery packs using superior lithium iron phosphate lifepo4 Cells - the next Generation of EnergyStorageAPPLICATION:Boats/Kayaks/Marine: RUIXU LiFePO4 batteries offer tremendous advantages for powering small boats and kayak motors. Communications equipment:many of our customers are using LiFePO4 batteries to replace lead acid and NiMh batteries for radio communications equipment including ham radio.

E-bikes / e-scooters / small vehicles:many of our customers are using LiFePO4 batteries for e-bikes/e-scooters E-wheelchair to replace lead acid batteries. Electric golf cart:ruixu lifepo4 batteries can be used to power electric golf caddies which are used to carry golf clubs across golf courses. Lithium iron battery for rv | marine | energy storage | backup system | popwersports | Eletric vehicle | solar| UPS |forklift | motor home |camping car |boat |caravan |wind energy | telecommunication systems |cabinsEnergy Storage: LiFePO4 batteries when combined with converters and inverters can be used as an energy storage solution.

LiFePO4 12V 200Ah Lithium Iron Phosphate Battery Pack, Light Weight LiFePO4 Battery for RV, Solar, Marine, and Off-Grid Applications BMS included #ad - Cabins battery, wind energy battery, telecommunication systems battery, off grid system battery Size:278*180*280mm | weight:26kgs.1c max charge rate | 3c max discharge rate |≥2000 times cycle life. Very important: pls contact with us about the installation info if you do not know how to use the BATTERY!***.

More information about RUIXU #ad

12 Circuits with Negative Bus & Cover - Blue Sea Systems ST Blade Fuse Block

#ad
Blue Sea Systems 5026 #ad - Can be used for 24-hour circuits. Cover satisfies abyc/uscg requirements for insulation, incorporates an easy to open push button latch providing easy access to fuses, storage for two spare fuses. 3. 32"w x 6. 5"h x 1. 52"d. St blade fuse block - 12 circuits with negative bus and cover. Positive distribution bus with #10-32 stud.

Fuses sold separately. Accepts ato and ATC fast acting blade fuses. Fuse block, atc/ato, w/negative bus and cover, mfg# 5026, 12 circuit, 32VDC max W/30Amp max per circuit & 100Amp per block.

More information about Blue Sea Systems 5026 #ad


Similar products



Blue Sea Systems MaxiBus 250A BusBar with Four 5/16

#ad
Blue Sea Systems 2127-BSS #ad - 250a maxibus busBar with 4 studs. Accepts ato and ATC fast acting blade fuses. Positive distribution bus with #10-32 stud. Max voltage: 300v aC/ 48V DC. Continuous rating: 250A AC/DC. Cover satisfies abyc/uscg requirements for insulation, incorporates an easy to open push button latch providing easy access to fuses, storage for two spare fuses.

Blue Sea Systems MaxiBus 250A BusBar with Four 5/16 #ad - Bus material - tin platted copper cda 110/uns c1100 insert molded stainless steel studs eliminate need for securing nut and allow high torqueing for excellent electrical contact Raised bus provides easy access to multiple wires on a single stud. St blade fuse block - 12 circuits with negative bus and cover.

Can be used for 24-hour circuits. Ul 94-v0 rated base material resists high heat, tin plated pure electrical copper for maximum conductivity. 2 mounting holes accept #10 M5 screws.

More information about Blue Sea Systems 2127-BSS #ad


Similar products



SELTERM UL Listed Heavy Duty Wire Lugs Battery Cable Ends Bare Copper Eyelets Tubular Ring Terminal Connectors

#ad
SELTERM #ad - Ul 94-v0 rated base material resists high heat, tin plated pure electrical copper for maximum conductivity. The copper eyelet connectors are rated for up to 600 volts and tested to ANSI/UL 486 standard. Can be used for 24-hour circuits. St blade fuse block - 12 circuits with negative bus and cover. Copper tubing used for producing the battery cable lugs meet ASTM B 188 electrical grade standard.

2 mounting holes accept #10 M5 screws. Heavy duty battery cable lugs from SELTERM are manufactured using industry leading manufacturing processes to guarantee a high-quality product. Furthermore, the copper battery lugs are both UL and CUL listed to ensure optimal performance once installed. Can be Crimped or Soldered.

SELTERM UL Listed Heavy Duty Wire Lugs Battery Cable Ends Bare Copper Eyelets Tubular Ring Terminal Connectors #ad - Positive distribution bus with #10-32 stud. Heavy duty construction for Enhanced High Temperature Durability. The copper lugs also meet S. A. E conductivity standards and are RoHS compliant. Cover satisfies abyc/uscg requirements for insulation, incorporates an easy to open push button latch providing easy access to fuses, storage for two spare fuses.

Made from 100% annealed Electrolytic Grade Copper for Max Conductivity.

More information about SELTERM #ad


Similar products



SELTERM UL Listed Marine Grade Tinned Copper Wire Lugs Heavy Duty Battery Cable Ends Eyelets Ring Terminal Connectors

#ad
SELTERM #ad - Ul tested & Approved. Can be Crimped or Soldered. Ul 94-v0 rated base material resists high heat, tin plated pure electrical copper for maximum conductivity. Made from 100% annealed Tinned Copper for Max Current Flow. The battery Cable lugs meet S. A. E conductivity standards and are tested to UL 486 with voltage rating of up to 600 V.

Can be Crimped or Soldered. Cover satisfies abyc/uscg requirements for insulation, incorporates an easy to open push button latch providing easy access to fuses, storage for two spare fuses. Accepts ato and ATC fast acting blade fuses. To ensure corrosion resistance the tin-plated lugs are salt spray tested to ASTM B 117.

SELTERM UL Listed Marine Grade Tinned Copper Wire Lugs Heavy Duty Battery Cable Ends Eyelets Ring Terminal Connectors #ad - Selterm marine grade copper Lugs are manufactured using industry leading processes to guarantee a high-quality product. Positive distribution bus with #10-32 stud. Close end pad seals Out Moisture Keeping Cables Dry. 2 mounting holes accept #10 M5 screws. Max voltage: 300v aC/ 48V DC. Continuous rating: 250A AC/DC.

Can be used for 24-hour circuits.

More information about SELTERM #ad


Similar products



GoWISE Power PS1003 Pure SINE Wave Inverter 2000w Cont/4000w Peak

#ad
Power TechON PS1003 #ad - Go wise power inverter is an advanced tool of power conversion. St blade fuse block - 12 circuits with negative bus and cover. Can be used for 24-hour circuits. 250a maxibus busBar with 4 studs. Pure sine inverters are a stable power source with 2000W continuous power and 4000W surge power with low harmonic distortion.

Ul 94-v0 rated base material resists high heat, tin plated pure electrical copper for maximum conductivity. Corrosion free Ideal for Marine Automotive or Outdoor Use. This inverter is an excellent tool to use during power failure emergencies and guarantees maximum efficiency with computers, sensitive equipment and more.

Inverter also comes with an LED light that indicates the problem. Your purchase comes with black and red cables with ring terminals, a remote switch, an inverter with 3 AC sockets and 1 USB port 5V, and a detailed instruction manual. Continuous rating: 250A AC/DC. It can be used in cars, vessels, during camping and in power failure emergencies.

GoWISE Power PS1003 Pure SINE Wave Inverter 2000w Cont/4000w Peak #ad - Heavy duty construction for Enhanced High Temperature Durability. The ps1003 features 5 kinds of protection systems: Thermal protection, Under Voltage protection, Overload protection, Over Voltage protection, Low Voltage protection alarm. Close end pad seals Out Moisture Keeping Cables Dry. Gowise power pure sine power inverter 2000w continuous/4000w surge, Remote Switch, 12v dc to 120v ac w/ black and Red Cables w/ Ring Terminals, 5 kinds of Protection Systems and 4 Output Sockets.

More information about Power TechON PS1003 #ad


Similar products



SHURFLO 4008-101-A65 New 3.0 GPM RV Water Pump Revolution, 12V

#ad
Pentair 4008-101-A65 #ad - Close end pad seals Out Moisture Keeping Cables Dry. Ul tested & Approved. 250a maxibus busBar with 4 studs. Ul tested & Approved. Mounts in any position. Made from 100% annealed Electrolytic Grade Copper for Max Conductivity. Can be Crimped or Soldered. Can be used for 24-hour circuits. Shurflo new revolution fresh water pump design was created with a unique one-piece diaphragm and internal by-pass, assuring long life and top performance in all plumbing systems.

Heavy duty construction for Enhanced High Temperature Durability. Cover satisfies abyc/uscg requirements for insulation, incorporates an easy to open push button latch providing easy access to fuses, storage for two spare fuses. Shurflo quality reputation has been built on the reliability and depend ability of every pump we build.

SHURFLO 4008-101-A65 New 3.0 GPM RV Water Pump Revolution, 12V #ad - 2 mounting holes accept #10 M5 screws. Made from 100% annealed Tinned Copper for Max Current Flow. Ul 94-v0 rated base material resists high heat, tin plated pure electrical copper for maximum conductivity. St blade fuse block - 12 circuits with negative bus and cover. The 4008 revolution fresh water automatic demand pump is super quiet, thermally protected and can run dry without damage.

Brand new shurflo 12v RV water pump 3.

More information about Pentair 4008-101-A65 #ad


Similar products



EPEVER MPPT Solar Charge Controller 40A 150V PV Solar Panel Controller Negative Ground W/ MT50 Remote Meter + Temperature Sensor PC Monitoring CableTracer4215BN

#ad
Epsolar Tracer4215BN-MT50 #ad - 250a maxibus busBar with 4 studs. You will find the software download link printed on the inside of the packing or contact us to get the download link. The package included the following item: 1. Made from 100% annealed Electrolytic Grade Copper for Max Conductivity. Ul 94-v0 rated base material resists high heat, tin plated pure electrical copper for maximum conductivity.

Made from 100% annealed Tinned Copper for Max Current Flow. Ul tested & Approved. Close end pad seals Out Moisture Keeping Cables Dry. 40a mppt solar charge controller with Remote Meter And Temperature sensor / PC monitoring cable. Gowise power pure sine power inverter 2000w continuous/4000w surge, 12v dc to 120v ac w/ black and Red Cables w/ Ring Terminals, Remote Switch, 5 kinds of Protection Systems and 4 Output Sockets.

EPEVER MPPT Solar Charge Controller 40A 150V PV Solar Panel Controller Negative Ground W/ MT50 Remote Meter + Temperature Sensor PC Monitoring CableTracer4215BN #ad - Ideal use in cars, vessels, and for power failure emergencies and guarantees maximum efficiency with computers, sensitive equipment, and more.5 protection systems: thermal protection, Over Voltage protection, Overload protection, Under Voltage protection, Low Voltage protection alarm. Total harmonic distortion thd.

Positive distribution bus with #10-32 stud. Heavy duty construction for Enhanced High Temperature Durability. St blade fuse block - 12 circuits with negative bus and cover.

More information about Epsolar Tracer4215BN-MT50 #ad


Similar products



TEMCo Hammer Lug Crimper Tool 5 Year Warranty

#ad
TEMCo TH0007 #ad - 2 mounting holes accept #10 M5 screws. Ul tested & Approved. Close end pad seals Out Moisture Keeping Cables Dry. Step 3 when hammer impact feels solid, the crimp is complete. Made from 100% annealed Tinned Copper for Max Current Flow. Can be used for 24-hour circuits. Step 2 with crimper on solid surface, strike crimp ram with hammer 1-2 times.

Ul tested & Approved. Note: some crimpers come with a gauge, but with variations in wire, terminal wall thickness and material used, this feature is a recipe for bad crimps. St blade fuse block - 12 circuits with negative bus and cover. Heavy duty construction for Enhanced High Temperature Durability. Cover satisfies abyc/uscg requirements for insulation, incorporates an easy to open push button latch providing easy access to fuses, storage for two spare fuses.

TEMCo Hammer Lug Crimper Tool 5 Year Warranty #ad - Can be Crimped or Soldered. Corrosion free Ideal for Marine Automotive or Outdoor Use. Continuous rating: 250A AC/DC. Made from 100% annealed Electrolytic Grade Copper for Max Conductivity. Accepts ato and ATC fast acting blade fuses. Once the terminal completely envelopes the wire, the crimper will not move and when struck will feel "solid".

More information about TEMCo TH0007 #ad


Similar products



Victron BatteryProtect 12/24V-100A

#ad
Victron Energy BPR000100400 #ad - The batteryprotect disconnects the battery from non essential loads before it is completely discharged which would damage the battery or before it has insufficient power left to crank the engine. Ul tested & Approved. 2 mounting holes accept #10 M5 screws. Max voltage: 300v aC/ 48V DC. Corrosion free Ideal for Marine Automotive or Outdoor Use.

Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the alarm has been activated. Can be used for 24-hour circuits. Positive distribution bus with #10-32 stud. Can be Crimped or Soldered. Over voltage protection to prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V.

Victron BatteryProtect 12/24V-100A #ad - Cover satisfies abyc/uscg requirements for insulation, incorporates an easy to open push button latch providing easy access to fuses, storage for two spare fuses. Ignition proof no relays but MOSFET switches, and therefore no sparks. St blade fuse block - 12 circuits with negative bus and cover. Ul tested & Approved.

The alarm output is typically used to activate a buzzer, LED or relay. A special setting for li-ion batteries In this mode the Battery Protect can be controlled by the VE.

More information about Victron Energy BPR000100400 #ad


Similar products



Red & Black 5/16" 4 Stud Power Distribution Block -BUSBAR- With Cover

#ad
JQuad #ad - Positive distribution bus with #10-32 stud. These blocks allow for multiple connections to positive and negative systems. Can be used for 24-hour circuits. Can be Crimped or Soldered. High quality 4 point power distribution block. Ul tested & Approved. Max voltage: 300v aC/ 48V DC. Close end pad seals Out Moisture Keeping Cables Dry.

Ul 94-v0 rated base material resists high heat, tin plated pure electrical copper for maximum conductivity. Can be Crimped or Soldered. Ul tested & Approved. Heavy duty construction for Enhanced High Temperature Durability. Each block can maintain multiple connections, making them flexible and robust for a variety of uses.

Red & Black 5/16" 4 Stud Power Distribution Block -BUSBAR- With Cover #ad - Close end pad seals Out Moisture Keeping Cables Dry. Made from 100% annealed Tinned Copper for Max Current Flow. Accepts ato and ATC fast acting blade fuses. Gowise power pure sine power inverter 2000w continuous/4000w surge, Remote Switch, 12v dc to 120v ac w/ black and Red Cables w/ Ring Terminals, 5 kinds of Protection Systems and 4 Output Sockets.

Ideal use in cars, vessels, and for power failure emergencies and guarantees maximum efficiency with computers, sensitive equipment, and more.5 protection systems: thermal protection, Under Voltage protection, Overload protection, Over Voltage protection, Low Voltage protection alarm.

More information about JQuad #ad


Similar products